| 21CIG15031000 | Stainless Steel Push Handle for Eyebath Pull Rod Control for Shower |
||
| Pipes | : | Stainless Steel | |
| Bowl | : | Stainless Steel or ABS Plastic | |
| Showerhead | : | Stainless Steel or ABS Plastic | |
| Water Inlet | : | 1“ | |
| Waste Outlet | : | 1 1/4” | |
| Water Flow | : | 11,5 lt/min (Eyewash) 75 lt/min (Shower) | |
| Total Weight | : | 20,500 kg (SS) – 18,300 kg (ABS) | |
| Packed Dimensions | : | H x W x D mm : 860 x 350 x 250 | |
| 21CIG15031500 | Galvanised and Painted Push Handle for Eyebath Pull Rod Control for Shower |
||
| Pipes | : | Galvanised and Painted | |
| Bowl | : | Painted Steel or ABS Plastic | |
| Showerhead | : | Painted Steel or ABS Plastic | |
| Water Inlet | : | 1“ | |
| Waste Outlet | : | 1 1/4” | |
| Water Flow | : | 11,5 lt/min (Eyewash) 75 lt/min (Shower) | |
| Total Weight | : | 21,500 kg (Galv.) – 19,300 kg (ABS) | |
| Packed Dimensions | : | H x W x D mm : 860 x 350 x 250 | |
| 21CIG15032000 | Stainless Steel Treadle Foot Control Eyebath Pull Rod Control for Shower |
||
| Pipes | : | Stainless Steel | |
| Bowl | : | Stainless Steel or ABS Plastic | |
| Showerhead | : | Stainless Steel or ABS Plastic | |
| Water Inlet | : | 1“ | |
| Waste Outlet | : | 1 1/4” | |
| Water Flow | : | 11,5 lt/min (Eyewash) 75 lt/min (Shower) | |
| Total Weight | : | 21,400 kg (SS) – 19,200 kg (ABS) | |
| Packed Dimensions | : | H x W x D mm : 860 x 350 x 250 | |
| 21CIG15032500 | Galvanised and Painted Treadle Foot Control Eyebath Pull Rod Control for Shower |
||
| Pipes | : | Galvanised and Painted | |
| Bowl | : | Painted Steel or ABS Plastic | |
| Showerhead | : | Painted Steel or ABS Plastic | |
| Water Inlet | : | 1“ | |
| Waste Outlet | : | 1 1/4” | |
| Water Flow | : | 11,5 lt/min (Eyewash) 75 lt/min (Shower) | |
| Total Weight | : | 22,400 kg (Galv.) – 20,200 kg (ABS) | |
| Packed Dimensions | : | H x W x D mm : 860 x 350 x 250 | |
| 1. Adequate Water Flow | : |
Emergency Safety Showers should deliver a minimum
of 75 liters/min (20 gallons / min) from a water pressure of 2.1 Bar (30
psi).Showerheads should produce a conical deluge of water with a
diameter of 50 cm at 150 cm from the floor surface when spraying from a
height of between 208-244 cm, and the center of this spray pattern
should be 40 cm from any obstruction. Eye/Facewash Fountains must
provide a continuous effective minimum flow of water in the region of
11.5 liters/min (3 gallons/min) at a height of 84-144 cm.
|
| 2. Ease Of Operation | : |
Activation device must be simple to use and easily
accessible – even if the victim has impaired vision.Stay-open ball
valves operated either by hand full leavers, panic bars or a walk-on
foot control enable an Emergency Shower to be operated quickly and
efficiently delivering a continuous drench for 15 minutes, allowint the
casualty to remove any contaminated clothing without having to hold on
to a spring return valve.
|
| 3. Instant and Operation | : |
Water supply valves must open quickly and simply as maximum flooding action must be provided within 1 second.
|
| 4. Reliability of Equipment | : |
Units must be capable of performing their required
service even after long periods of idleness.Top quality valves operated
by jam-proof, robust and corrosion-resistant actuating devices are
essential for total reliability.
|
| 5. Installation Tips | : |
Emergency Safety Showers and Eyewash Fountains
Units should be within 10 seconds reach if an accident occurs for strong
acids and caustics they must be immediately adjacent to the
hazard.Emergency Showers and Eye/Facewash units should be on the same
level as the hazard.Only potable water should be used the inlet water
pressure must meet the manufacturers recommended minimum (2.1 bar = 30
psi) and the supply pipe should have at least the same diameter as the
inlet pipe on the equipment.
|
| 6. Battling Corrosion | : |
Emergency Showers and Eyewash Fountains must be
corrosion resistant.Corrosion resistant outer jackets or other
protective coatings are recommended on strong corrosive environments.
Plastic coating over stainless steel prevents corrosion on operating
handles and linkages. Use of stainless steel nuts, bolts and washers is
recommended.
|
| 7. Test Program | : |
Emergency Safety Showers and Eyewash Fountains
shall be visually inspected everyday to make certain quick and easy
access is ensured. Water flow should be checked at least once a week to
“flush the line, and to verify proper operation”. Eyebaths and
Eye/Facewash Fountains should be tasted daily and cleaned regulary.
|
Free Ongkir Wilayah Jakarta dan Tangerang Sekitarnya
Informasi lebih lanjut bisa menghubungi :
|


Posting Komentar